Quick Answer
The most common diagnostic error is treating the visible leak as the location of the defect. Water enters at one interface, travels behind a finish or along a cavity, and exits somewhere else entirely — often a storey below and two bays across.
A workable sequence narrows the search in four moves:
| Step | What it eliminates |
|---|---|
| Read the pattern | Whether this is systemic or local |
| Terminate the water at the top | Which elevation the entry is on |
| Test by isolation | Which interface is responsible |
| Open and inspect | Which component within that interface failed |
Each step eliminates options. Skipping to the fourth step is faster on the day and slower overall, because the wrong interface gets repaired and the leak returns.
1. Start With the Pattern, Not the Joint
Before touching anything, establish how the water behaves. Four observations do most of the work:
- Timing. Does it appear during rain, hours after rain, or only with wind-driven rain?
- Distribution. One joint, one elevation, one detail, or scattered across the building?
- Progression. Has it been constant, seasonal, or worsening?
- Association. Did it start after installation, after a repair, after a façade cleaning, or after nearby construction?
Wind-driven rain that produces leaks on one face and not another points to a pressure and drainage question rather than an adhesion failure. Water that arrives hours after rain stops suggests it is travelling along a cavity, which changes where you look. A leak that began after cleaning usually involves a cleaning agent or a pressure jet, not the sealant’s age.
Recording these four before any inspection protects the investigation from the most human failure: deciding the cause on the first visit and spending the rest of the project confirming it.
2. Separate Water Management From Sealing
A façade is not waterproofed by sealant alone. It is waterproofed by a system: cladding, flashing, drainage cavities, weep paths, gaskets, and sealant in specific roles.
Three failure modes look identical from inside the building:
| Mode | Where the defect is |
|---|---|
| Sealant failure | The bead has separated, cracked, or was never continuous |
| Detailing failure | Flashing laps the wrong way, a drainage path is blocked, a transition is open |
| System failure | The assembly relies on the sealant as the only barrier, which it was never designed to be |
The third is the one that produces repeat visits. Resealing a joint that was never meant to be the primary barrier buys months, not years.
Telling the three apart starts with the failure evidence itself, which is catalogued in common causes of facade sealant failure.
Checking the joint design before ordering material is the difference between a repair and a cycle. The detail set for the relevant assembly is summarised in windows, doors and joint solutions.
3. Isolate By Elevation Before You Isolate By Joint
If the entry point is unknown, work top-down.
Close or temporarily seal the most likely upper terminations first — parapet copings, horizontal joints, roof-to-wall junctions — and observe. A single storey of scaffolding and one day of observation eliminates a whole category of candidates.
This is unglamorous and it is the step most often skipped, because the visible symptom is usually at eye level and the entry is usually above it.
Where the building is tall or access is expensive, a hose test on a defined area is more informative than another inspection from inside. Water applied at a known rate to a known area, with the interior observed, is the only way to convert a suspicion into a finding.
Water testing introduces water into the building by design. It should be planned, controlled and executed by competent personnel, with the interior protected and the test area defined in advance.
4. Read the Sealant Correctly
When a joint is opened, the failure pattern is diagnostic — but only if it is read correctly.
| What you see | What it usually indicates |
|---|---|
| Clean separation at the substrate face | Adhesion loss: preparation, contamination, or incompatibility |
| Cohesive tear within the bead | Movement beyond capacity, or over-stressed geometry |
| Bead cracked along its length | Joint movement, or insufficient cure before movement |
| Bubbles or voids inside the bead | Application conditions, or moisture during cure |
| Sealant bonded but water still passing | The joint is not the entry — look at the assembly |
The first and third are frequently confused, and they have opposite remedies. Adhesion loss is a surface problem; cohesive failure is a design or movement problem. Replacing the sealant fixes the first and repeats the second.
Where the surface is the suspected problem, the checks that distinguish contamination from incompatibility are set out in what to check across glass, aluminium and stone.
5. Distinguish Joint Geometry From Joint Condition
Two joints with the same sealant in the same condition can behave differently because of how they were built.
Check, on the opened joint:
- Width and depth as built against the drawing.
- Depth-to-width ratio, and whether it falls within the product’s stated application window.
- Backer rod presence and position — a joint with no backer has no defined depth and no bond breaker.
- Bond breaker continuity — a bead bonded on three faces cannot move.
- Continuity of the seal at corners, transitions and terminations.
A joint drawn at 12 mm and built at 5 mm needs a different treatment from the same sealant in the drawn geometry, and no product change compensates for it. This is why “which sealant should we use” is often the wrong first question.
6. Decide What You Are Actually Repairing
Once the entry is located and the mechanism identified, the repair scope follows. Four outcomes cover most cases:
Re-seal. The joint geometry and the assembly are sound; the bead failed on adhesion or continuity. Scope is preparation plus new bead.
Re-detail. The assembly has a water-management defect. Resealing alone will not last, because the sealant is being asked to do a job the detail should do.
Re-build the joint. Geometry is out of tolerance, backer is missing, or bond breaker is absent. The joint needs to be reconstructed before it is sealed.
Investigate further. The entry has not been located with confidence. Doing work now spends money without reducing risk.
The temptation is always the first outcome, because it is the cheapest and can be done immediately. It is also the one most often followed by a second visit.
7. What to Send a Supplier — and What Not To
A sealant supplier can help with product suitability. It cannot diagnose a building, and a request framed as “we have a leak, which product” will produce a generic recommendation that helps nobody.
Useful information to send:
- Substrates on both faces, with finishes.
- Joint width and depth as built.
- The failure pattern, photographed at the opened joint.
- Whether the joint is movement or static.
- Exposure: orientation, wind-driven rain, standing water.
- Repair constraints: access, downtime, temperature, occupied building.
- The existing product, if known.
With those seven, a supplier can say whether the proposed replacement fits the geometry and the movement, and whether a different class is required. Without them, the answer is a catalogue page.
8. The Diagnostic Record
One page per investigation, kept with the building file. It is what turns a repair into evidence.
| Field | Content |
|---|---|
| Reported symptom | Location, timing, conditions, progression |
| Affected area | Elevations, joints, extent |
| Pattern assessment | Local or systemic, wind-related or not |
| Isolation steps | What was closed, tested, observed |
| Opened joint findings | Failure mode, geometry as built, backer condition |
| Probable mechanism | Adhesion, movement, detailing, or assembly |
| Repair scope | Re-seal, re-detail, re-build, or further investigation |
| Product specified | Model and the basis for selecting it |
The record matters most on buildings with repeat leaks. Two visits with no record is a third visit; two visits with a record is a diagnosis.
Conclusion
Leak diagnosis is elimination, not inspection. Read the pattern, isolate by elevation, test the interface, and only then open the joint and read the sealant.
The sealant is often the wrong thing to blame and the easiest thing to replace, which is precisely why it gets replaced first and the leak comes back.









